Plumbing Basics: An Essential for When Installing a Bathtub
Plumbing Basics: An Essential for When Installing a Bathtub
Blog Article
This post listed below on the subject of A Step-by-Step Guide to Installing a Bathtub is exceptionally entertaining. Give it a try and make your own results.
Setting up a bathtub isn't exactly rocket science, but it does require strong plumbing, woodworking, and also often, tiling skills. Replacing an old bathtub with a brand-new one is also a reasonably difficult project. If the old tub is conveniently available, the job can move easily; if you have to open up a wall surface to eliminate the old bathtub as well as position the brand-new bathtub, the job is much harder. In either situation, the job is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub and embeded in the brand-new one. Ensure you have actually qualified on your own for the job and also are comfortable attempting it. Instead of employing a contractor to take control of a halfway-completed project, it is better to think about employing one prior to you start. Possibilities are you may require a professional plumber to make tube connections.
This write-up will assist you mount a new tub in your washroom if you have actually already purchased a brand-new tub as well as don't need to change the arrangement of your previous water system pipes.
Your devices and material list ought to make up the following:
Preparing for the Setup
To start with, the supporting frame provided with the bath should be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath and the faucets. On a plastic bathroom, it is also reasonable to fit a sustaining plate under the faucets system to prevent stress on the bathtub.
Fit the adaptable faucet ports to the bottom of both taps making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize every one of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your installment, then the first thing you should do is detach the supply of water. After doing so, activate the faucets to drain pipes any type of water continuing to be in the system. The process of removing the existing taps can be quite troublesome because of the restricted gain access to that is commonly the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will certainly come from the pipelines. When the supply pipelines have been removed, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new taps, contrast the pipe connections on the old taps to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is required for the new taps to fit.
Setting up the Tub
Utilizing both wooden boards under its feet, put the tub in the needed setting. The wood boards are practical in uniformly spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also changing the feet on the tub until the spirit level reviews level.
To install taps, fit all-time low of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Switch on the water supply as well as examine all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill up the bathtub and also inspect the overflow outlet and also the regular outlet for leaks.
Lastly, deal with the bath paneling as defined in the manufacturer's instruction manual. Tiling and also securing around the bathtub should wait until the bath tub has been used a minimum of once as this will settle it into its final setting.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the placing opening in the bath/basin making certain that the washing machines are in location between the faucet as well as the sink. Secure the faucet in place with the supplier supplied backnut. Once the faucet is securely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with typical tap ports. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bathroom fulfills the tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to break an inflexible seal, causing the water to penetrate the wall between the bath as well as the tiling, causing difficulties with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealers to assimilate your components and also installations. They are offered in tubes and also cartridges, and also can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Bear in mind to always fill the bath tub with water prior to securing, to allow for the movement experienced when the bathtub is in usage. The sealer can fracture rather early if you do not take into account this activity before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise conveniently available on the market. It is suggested to fit the tiles utilizing waterproof or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I'm certainly very drawn to How to Install a Bathtub Yourself and I am assuming you appreciated the entire blog posting. For those who appreciated our blog entry if you please don't forget to pass it around. I praise you for your time. Please check our blog back soon.
Tap dripping? Phone! Report this page